How To Repair A Iphone 5s Screen

Introduction

Learn how to replace your iPhone 5s screen. This part comes with the front-facing photographic camera, earpiece speaker and sensor cable already installed, making for an easier repair.

All you need to do is remove the old screen and transfer the domicile button to the new screen in guild for Touch ID (fingerprint scanning) to function.

Video Overview

• Earlier you go on, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

• Power off your iPhone before beginning disassembly.

• Remove the two 3.nine mm Pentalobe screws from either side of Lightning connector.



• If your display drinking glass is cracked, go along further breakage independent and prevent bodily harm during your repair past taping the glass.

• Lay overlapping strips of clear packing tape over the iPhone's brandish until the whole face is covered.

• This will keep glass shards independent and provide structural integrity when prying and lifting the display.

• Wear safety glasses to protect your eyes from any glass shaken free during the repair.

• In the post-obit steps you will be pulling the display up out of the phone body. The display is composed of a drinking glass screen and a plastic bezel with metal clips.

• Regardless of the tool you use, you lot need to exist certain you pull up the entire display.

• If the drinking glass begins to split from the plastic, as shown in the first image, slide a plastic opening tool between the plastic frame and the metal phone trunk to pry the metallic clips out of the instance.

• If yous are reassembling a phone with a separated display bezel, you may desire to place a thin strip of agglutinative betwixt the plastic bezel and the drinking glass to keep the phone closed.

• The next two steps demonstrate using the iSclack, a great tool for safely opening the iPhone that nosotros recommend for anyone doing more than ane repair. If you aren't using the iSclack, skip the next two steps.

• Close the handle on the iSclack, opening the suction-cup jaws.

• Identify the bottom of your iPhone in between the suction cups, confronting the plastic depth gauge.

• The top suction cup should rest just in a higher place the habitation push.

• Open up the handles to shut the jaws of the iSclack. Center the suction cups and press them firmly onto the top and bottom of the iPhone.

• Hold onto your iPhone securely and shut the handle of the iSclack to divide the suction cups, pulling the front panel upwardly from the rear case.

• The iSclack is designed to safely open your iPhone just enough to separate the pieces, simply not enough to impairment the home button cable.

• Peel the 2 suction cups off your iPhone.

• Skip the side by side 3 steps and continue on Step nine.

• If you don't have an iSclack, apply a single suction cup to lift the front console:

• Press a suction loving cup onto the screen, merely above the home push button.

• Be sure the cup is completely on the screen to get a tight seal.

• The forepart console is attached with clips, and there are several ribbon cables connecting it to the remainder of the phone. Your goal here is to release the clips and open up the phone only enough to disconnect the cables. Become slowly and carefully to avoid damage.

• Make certain the suction loving cup is firmly attached to the front panel associates well-nigh the abode push button.

• While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the habitation button end of the front end panel from the rear case.

• With a plastic opening tool, gently pry the edges of the rear case downward, abroad from the front end panel associates, while y'all pull up with the suction loving cup.

• Take your time and apply business firm, constant force. The front panel assembly is a much tighter fit than on most other devices.

• Practice non try to completely remove the front panel assembly from the rear case, as there are several frail ribbon cables connecting them.

• Pull the plastic nub to release the vacuum seal on the suction loving cup.

• Remove the suction cup from the screen.

• Open the telephone just plenty to reveal the metal subclass roofing the home push button cablevision.

• Do not open the telephone as well far or you adventure dissentious the home button cable, or the socket it plugs into. Keep the cablevision loose—if information technology is stretched taut, that's besides far.

• Only the phone'south original domicile button associates will be capable of using the Bear on ID functionality. If you rip the cable, installing a new abode button will merely restore ordinary home button functions, not the Touch ID features.

• Use the tip of a spudger to push the bracket free and remove information technology with tweezers.

• The next two steps employ to reassembly. Skip them and continue to Step 12 until reassembly.

• During reassembly, y'all volition need to reinstall the Impact ID cablevision bracket. The peak of the subclass needs to slide between the battery and Bear upon ID cablevision connector, in front of the metal tab. The bottom must latch down over the connector.

• Slide the top of the bracket over the Touch ID cable connector from left to correct.

• During reassembly, use the flat stop of a spudger to snap the front portion of the Touch ID cablevision bracket downward over the cable connector.

• If the bracket does non snap down flush, you may need to remove the bracket and slide it over the cable connector once more for a better fit.

• Utilize the tip of a spudger to pry the home button cable connector up out of its socket.

• Be sure yous're separating the cable connector from its socket, and not prying the entire socket up. The socket is on its own glued-down cable that tin be pried up if you lot aren't careful.

• Once the connector has been released, pull the domicile button cease of the assembly away from the rear instance, using the pinnacle of the telephone equally a hinge.

• Open the display to almost a 90º bending, and lean it against something to keep it propped upward while you're working on the phone.

• Add together a rubber band to keep the display securely in identify while you piece of work. This prevents undue strain on the display cables.

• In a compression, you tin use an unopened canned beverage to agree the display.

• Remove the two 1.6 mm Phillips #000 screws securing the metal battery connector bracket to the logic lath.

• Remove the metal battery connector bracket from the iPhone.

• Utilise the flat end of a spudger to gently pry the battery connector up from its socket on the logic board.

• Be very careful to merely pry up on the battery connector itself and not the socket on the logic lath. If you pry up on the logic board socket or the lath itself, y'all may destroy the socket or damage nearby components on the board.

• Remove the post-obit screws securing the front panel assembly cable bracket to the logic board:

• One 1.7 mm Phillips #000 spiral

• Ane one.2 mm Phillips #000 spiral

• One 1.three mm Phillips #000 spiral

• One more 1.7 mm Phillips #000 spiral

• This 1.vii mm screw tends to non exist attracted to a magnetized screwdriver. Take intendance not to lose it when removing.

• Information technology is especially important to go along rails of your screws in this footstep for reassembly. Accidentally using the i.3 mm screw or one of the 1.7 mm screws in the bottom right hole will result in significant damage to the logic board causing the phone to no longer boot properly.

• Be careful not to over-tighten the screws, and don't force them. If they don't fit easily when you are securing them, they may exist the wrong size.

• Remove the front end panel assembly cable bracket from the logic board.

• Employ a spudger or a fingernail to disconnect the front-facing camera and sensor cable.

• Brand sure the bombardment is disconnected earlier you disconnect or reconnect the cable in this step.

• Disconnect the LCD cable connector.

• When reassembling your phone, the LCD cable may pop off the connector. This can result in white lines or a blank screen when powering your phone dorsum on. If that happens, just reconnect the cablevision and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery.

• Finally, disconnect the digitizer cablevision connector.

• Remove the front panel assembly from the rear instance.

• Unscrew the unmarried captive Phillips #000 spiral securing the home button cable.

• The captive screw is attached to the home push button cable by a spring contact backing. During reassembly, ensure the contact is in the right orientation—on the side of the screw nearest the LCD.

• If your replacement function does not accept this convict screw and spring contact, y'all will need to transfer them to the new cablevision.

• Fold the dwelling house button cablevision down, out of the mode of the home button subclass.

• Remove the two one.4 mm Phillips #000 screws from the dwelling button subclass.

• Remove the home button bracket from the display assembly.

• Wedge the the tip of a spudger underneath the home button cable assembly.

• The habitation button cable is affixed by mild agglutinative.

• Gently work the spudger underneath the cablevision to separate the home button cable from the forepart panel assembly.

• Do not remove the home button notwithstanding, every bit it is still attached to the forepart panel assembly.

• If necessary, remove the record over the home push on the forepart side of your cracked front panel associates.

• Gently push button the height left corner of the abode button upward abroad from the front panel.

• Do non push the dwelling house push all the way through—you just need to get a corner free, and so that you can pry information technology free with a spudger.

• This membrane is very thin. If yous experience similar you're going to tear the push, apply heat and try over again.

• Peel the home button the rest of the way off of the display by prying gently with a spudger.

• Remove the dwelling house push button assembly from the front panel.

• The screen remains.

• If your replacement screen is missing any components that are nevertheless on the assembly you lot just removed, follow this guide to transfer them to the new part.

• If your replacement screen came with any protective plastic films that you don't encounter on the original brandish, be certain to pare them off before kickoff reassembly.

Determination

To reassemble your device, follow the higher up steps in reverse social club.

Compare your new replacement part to the original part. You may demand to transfer remaining components or remove adhesive backings from the new part before installing. Take your e-waste matter to an R2 or east-Stewards certified recycler. Repair didn't go as planned? Check out our Answers community for troubleshooting help.

Embed this guide

Choose a size and re-create the code beneath to embed this guide equally a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/iPhone+5s+Screen+Replacement/30962

Posted by: wilsonhimattim.blogspot.com

Share this post